Tension Gauge

Take the guessing out of your tension with the TOWA Tension Gauge. Perfect for embroiderers, the bobbin tension gauge consistently measures and sets accurate embroidery bobbin case tension every time. The tension gauge helps eliminate the bobbin thread from poking into the top stitches, prevents the top stitches from looping, and prevents those dreaded thread breaks. With no set up required, the TOWA tension gauge is ready to use right out of the box. The size M is recommended for longarm machines and the size L is recommended for the TL machines.

Using the Tension Gauge:

1. Remove the bobbin case from your machine, making sure the bobbin thread is out of the thread slot. Then place your bobbin case with the bobbin in it into the gauge slot. Snap the bobbin case into place.

2. Wind your bobbin thread around the two pulley wheels then around the plastic hook end on your tension gauge.

3. Pull your thread slowly, paying attention to the reading on the gauge. You are looking for a correct bobbin tension between 180 to 220 grams (up to 250 grams when embroidering caps).

• • Note: If your gauge is shown in units of 10’s, the correct bobbin tensions should be 18 to 22 grams.

4. If you are out of the 180-220 gram range, turn your bobbin case spring tension screw to tighten or loosen to get back into range.

Note: Before using the Tension Gauge, make sure your bobbin case is clean. The gauge needle should provide a steady reading. If you see the gauge needle giving a bouncing or erratic reading you could have a dirty or defective bobbin case Tip: Slide a business card back and forth under the bobbin tension spring to clear any dirt.

After adjusting your bobbin case tension, give it a test run.

1. First run a fill stitch test pattern.

2. See any top stitch looping? Tighten the main upper tension knob slightly until the looping disappears (looping can also occur if your bobbin tension is too tight).

3. Ideal thread tension for satin stitches should reveal 1/3 bobbin and 2/3 top thread color on the underside of the embroidery.

Note: Too much bobbin showing on the underside and/or showing on the topside usually means either the bobbin tension is too loose or the top thread tension is too tight.

Part Number: 400TM3 (size M) and 400TM1 (size L)

The large needle hole makes this throat plate ideal for sewing heavy-weight materials.

• This plate is designed for sewing with thicker weight fabric as well as a heavy amount of fabric to prevent your needle from tugging, resulting in damaging your regular stitch plate.

• Juki TL models include Juki TL 2010, Juki TL15, Juki TL2010Q, Juki TL2200, Juki TL2000Q, Juki TL 2000QI, Juki TL98, Juki TL18 Haruka, Juki TL2020PE, Juki 2200QVP Mini sewing machines.

This presser foot is designed specifically for sewing chain stitches.

• Use the left needle with this presser foot. (Be sure to remove the right and center needles before using this presser foot.)

Model & Part Number:

• MCS-1700QVP: 40177370

This presser foot is used for sewing together two pieces of fabric while creating gathers.

• Using the differential feed, gathers can be created in only the lower piece. You can adjust the amount of fabric that is gathered by changing the differential feed between 1.5 to 2.0
• Gathers can also be created in a single piece of fabric.

Series & Part Number

• MO-2800: 40138121
• MO-1000: 40138121
• MO-735: A9860-655-0A0C
• MO-114D/104D: A9860-655-0A0C
• MO-655: A9860-655-0A0C
• MO-654DE/MO-644: A9860-655-0A0C
• MO-623: A9860-655-0A0C
• MO-50e: 40131948
• MO-80CB: 40131948
• MO-1200QVP: A9860-655-0A0C
• MO-2000QVP: 40138121

This presser foot for free-motion sewing is open at the front so that the needle area is easy to see. It is used for free-motion sewing when the sewing machine is positioned longitudinally.

• This presser foot is useful for free-motion sewing when the sewing machine is positioned longitudinally with the machine head in front of you. It is also perfect to use with the free-motion table.

• Since the presser foot moves up and down together with the movement of the needle, thick seam can easily be crossed.

Works with all Juki TL Machines:

• • Juki TL models include Juki TL-18QVP Haruka, Juki TL-15, Juki TL-2020PE, Juki TL-2010, Juki TL-2010Q, Juki TL-2000Q, Juki TL-2000QI, Juki TL-98, Juki TL-2200QVP Mini sewing machines.

Part Number: 40166734

This presser foot is used to sew blind hem stitching, decorative flatlock or pin-tucks.

• This presser foot can be used with either the right or the left needle and has a guide plate that can be moved within a wide range.

• Since the seam width can be adjusted, this presser foot is also useful for decorating by sewing along a folded edge with decorative flatlock or with roll hem (pin-tuck) stitches.

Series & Part Number

• MO-2800: 40149058

• MO-1000: 40149058

• MO-735: A9521-634-0A0A

• MO-114D/104D: A9521-634-0A0A

• MO-655: A9521-634-0A0A

• MO654DE/MO-644: A9521-634-0A0A

• MO-623: A9521-634-0A0A

• MO-50e: 40131946

• MO-80CB: 40131946

• MO-1200QVP: A9521-634-0A0A

• MO-2000QVP: 40149058